Ron & Doug's Sales Camp https://www.pressurecleaningschool.com/events/houston-sales-training-school/

Search:

Type: Posts; User: clean2be; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    2,459

    Welcome to the club. Mike

    Welcome to the club.

    Mike
  2. Replies
    43
    Views
    40,388

    Hey Pat, my enclosed is a Carmate 6 x 12...

    Hey Pat, my enclosed is a Carmate 6 x 12 V-front.

    Mike
  3. Replies
    43
    Views
    40,388

    I did just the pickup to begin with, then went to...

    I did just the pickup to begin with, then went to open. I've had my enclosed for 15 years now. Other than the obvious higher cost of the enclosed, the two tradeoffs I'm not crazy about with the...
  4. Replies
    5
    Views
    2,536

    Pricing basically comes down to how much you need...

    Pricing basically comes down to how much you need to make per day and how much work/surface area can you clean per hour x 6-8 hrs. per day.

    A lot of traffic has moved over to Facebook.

    Mike
  5. Replies
    3
    Views
    2,300

    Have you tried running the engine with the low...

    Have you tried running the engine with the low oil sensor wire disconnected?

    Mike
  6. Replies
    3
    Views
    2,300

    Does it have a low oil sensor. Mike

    Does it have a low oil sensor.

    Mike
  7. Replies
    4
    Views
    725

    Do you have the injectors facing the correct...

    Do you have the injectors facing the correct direction?

    Mike
  8. Thread: Rust?

    by clean2be
    Replies
    4
    Views
    2,195

    You would be correct. Mike

    You would be correct.

    Mike
  9. Replies
    8
    Views
    4,928

    Excellent! The belt drive is far superior to the...

    Excellent! The belt drive is far superior to the direct drive...

    Mike
  10. Replies
    2
    Views
    1,915

    Welcome Jim! 4gpm is a good starting point. Don't...

    Welcome Jim! 4gpm is a good starting point. Don't purchase a direct drive! Personally, I prefer belt drive however, gear driven is good too. Belt driven is the smoothest running set-up. Direct drive...
  11. Replies
    726
    Views
    264,416

    Sticky: Welcome Carlos! Please do read and research the...

    Welcome Carlos! Please do read and research the topic.when pressure washing any resi or commercial building, it's more about the cleaning solutions used rather than pressure applied to the surface....
  12. Replies
    8
    Views
    4,928

    In most cases, a 4gpm pump won't need a buffer...

    In most cases, a 4gpm pump won't need a buffer tank. If you'll be working in an area which comprises mostly of submersible or jet pump systems, you may run into a supply problem.

    Most direct drive...
  13. Replies
    3
    Views
    749

    Sometimes, the surface cleaner cannot be beat...

    Sometimes, the surface cleaner cannot be beat when cleaning composite decking. Other times, the surface cleaner will cause a big headache. If you run your mix right, you won't need much pressure. If...
  14. Replies
    4
    Views
    2,164

    Welcome to the forum Matt! Mike

    Welcome to the forum Matt!

    Mike
  15. Thread: Check valve

    by clean2be
    Replies
    3
    Views
    1,097

    Well, obviously you can't remove the check ball...

    Well, obviously you can't remove the check ball and spring which is located in the injector body however, I don't run the additional check ball and spring which is typically found in the...
  16. Thread: Check valve

    by clean2be
    Replies
    3
    Views
    1,097

    Hey Al, are you referring to the check valve at...

    Hey Al, are you referring to the check valve at the end of the suction tube with the filter/strainer or in the body of the injector?

    Mike
  17. Replies
    4
    Views
    3,085

    You need to do one of three things. Install an...

    You need to do one of three things. Install an injector bypass and turn the valve to stop the soap, manually pull the siphon tube out of the chem tank or install a remote controlled shut off...
  18. Replies
    51
    Views
    13,029

    If running a 4gpm and high draw injector, you may...

    If running a 4gpm and high draw injector, you may need to step the rinse nozzles down to a number 6 or 7.

    With 225' of hose and number 8 nozzles, my Super Suds Sucker still pulls soap.

    Mike
  19. Replies
    4
    Views
    2,600

    As long as the paint is in good condition, you'll...

    As long as the paint is in good condition, you'll be fine. As already mentioned, go a little lite with the SH.

    Mike
  20. Welcome DJ. What's the GPM of your machine? ...

    Welcome DJ. What's the GPM of your machine?

    Mike
  21. Replies
    11
    Views
    5,117

    Same here, if the brick simply has regular dust...

    Same here, if the brick simply has regular dust and dirt to light green mold/algae, standard house wash mix. If heavier green to light black algae, a strong house wash mix. If it has progressed to a...
  22. Replies
    11
    Views
    5,117

    Also getting crazy busy and run out of time to...

    Also getting crazy busy and run out of time to check in with the board.

    Mike
  23. Replies
    8
    Views
    3,345

    Have you tried the 8.5% at nearly full strength?...

    Have you tried the 8.5% at nearly full strength? True 8.5% is about the weakest we would want to be using however, it will kill algae if the stains are algae. Is it possible that the stains are...
  24. Replies
    7
    Views
    2,895

    Welcome to the forum Tod. Mike

    Welcome to the forum Tod.

    Mike
  25. Replies
    16
    Views
    6,991

    I don't use any waxes however, I suppose you...

    I don't use any waxes however, I suppose you could try one. Eventually, it will either wash off or be burned off from the sun. You won't be able to stop the oxidation however, you may slow it's...
Results 1 to 25 of 328
Page 1 of 14 1 2 3 4